Supplement to the instruction manual for the products from 2020 onwards. Subject - GAIN PRE SELECTION ...
The following text describes the device of a "GAIN pre-selection" - we call this "GAIN PRE SELECTION" on the LUMINARE, which serves the sole purpose of selecting low-impedance headphones or "High Efficency" headphones, without an imperceptible "noise carpet" in the OTL mode on the LUMINARE.
It was not our plan to operate headphones of impedances in the range below 50 ohms on the LUMINARE in OTL mode to exclude a mismatch. However, it has been shown in the past that the OTL mode has such an outstanding performance that we do not want to close ourselves any longer to the wish to operate also low impedance headphones in OTL mode. For your peace of mind - the amp will not be damaged.
At 20 ohms in OTL mode, the LUMINARE still produces about 2 x 1 watt and at 40 ohms 2 x 1.5 watts. From therefore a lack of power is not to be expected and one recognizes also tendency at this example the increase of the achievement with increase of the headphone impedance and culminates with 200 ohm headphones with considerable 2 x 8 Watts.
The GAIN switch, which was previously located in the LUMINARE, is expanded by a 3rd position. Until now, you could switch + 10 dB to it when listening to STAX, if necessary.
From 2020 - so the plan - this switch will be replaced by an ON - OFF - ON switch. Thus, three settings will be available. The center position of the switch, which reflects OTL in the familiar mode. So without any change in gain, as you already know it.
Then for the STAX mode the increase of the gain by + 10 dB when you push the switch up and now new, the decrease of the gain by -10dB when you push the switch down. In the lowered gain mode ( - 10 dB ) the control range of the potentiometer is correspondingly increased and thus also finer dosable.
With this in mind, we wish you continued enjoyment of your product and assure you that we will always strive to provide excellent service.
Your Team AudioValve - Kassel, December 2019
simply the best unique all in one headphone amplifier its planet ...
The AudioValve Luminare/DAC is a supurb tube headphone amplifier and DAC capable of driving Electrostatic, Planar Magnetic and Dynamic headphones to their full potential offering state of the art results. AudioValve puts most of their budget towards the sound quality of their design and components rather than all of the audio jewelry and marketable designs featured by some of the comparable sounding amplifiers on the market. On sound alone it outclasses its price point, as for performance, design, fit and finish it far exceeds our expectations and represents a truely exceptional product at double or triple it’s price catagory.
Sound wise this amplifier delivers great tonality, world class 3D sound stage, a noise floor on par with all but the very best valve based amplifiers, and macro and micro dynamics in spades.
The sound quality of the Luminare is of absolute top reference level for a headphone tube amplifier. The pros to this are a very low noise floor, low distortions, high frequence range, high damping, very natural and musical tonality, wide impedance matching, perfect open soundstage and so on. This amp isn’t for the weak of heart – it is an audioholic’s dream. Highly recommended is an understatemen.
AudioValve offers an in-house DAC developed by Manfred Penning. The description can be found under PRODUCTS / DAC. For those who do not want to play their HIGHRES files via our DAC, AudioQuest now offers an inexpensive option with the "DRAGONFLY". This USB - DAC can also be connected to an iPhone with the help of an adapter cable and who owns a TIDAL subscription - which now also plays MQA Masterquality Files - really hears music at the highest level even for a small fee. So, the DragonFly on the one hand via the adapter cable to the mob phone, the other side of 3.5 mm jack in the analog input of Luminare and enjoy the maximum sound quality its amp.
with remote control and prepared for DAC setup
AWARD - best headphone amplifier 2016 more then 1000,- USD
"The best is the enemy of the good ... "
AUDEZE present here goods on the show CANJAM 2015 in Cosa Mesa with AudioValve`s LUMINARE ...
of course you could also use at Audeze on the CANJAM another established headphone amplifier - but you didn't,
you had consciously chosen to Luminare. Why Audeze had probably done it - everyone knows the answer .....
The story of LUMINARE.
I do not really know why I have driven this project forward not many years ago. I think I was busy with a lot of other developments as well as trivial things like earning money for example. Perhaps mine is simply unaware that their headphones and amplifiers are experiencing a large hipe for years. Anyway, the beginning of 2014 resulted in discussion with colleagues that I would have some products in my program that seemed almost ideally suited to put with the requirements of the headphone market apart.
No sooner said than done. First, the IMPEDANCER befell a technical revision, it was expanding the range of applications for the RKV Mark 2 significantly, especially as a female teflon connector for headphones STAX was inter alternates. The bias voltage was obtained from the voltage signal, so no external power supply is in advance required. VERTO was born and VERTO laid the foundation for all further considerations in this topic, culminating now in the product with the name LUMINARE.
I can excuse at this point only for me actually that I started so fundamentally important development in the headphones sector so late (I slept through) and had thus deprived the public a potentially groundbreaking product. Many of you have their money invested now possibly poorly because there was nothing else on the market - that really am sorry. But now back to Luminare.
It seemed to me as the basis for such a project, the OTL circuit of the RKV downright awesome. First, they had already claimed stable over decades in the market and on the other they had characteristics that should prove to be just the Luminare be extremely efficient and more full development. There would be for example the superior damping factor, low internal resistance, high bandwidth, and not least the low harmonic distortion he always particularly distinguished the RKV.
Now it was in principle "only" about output transformers so be interconnected in the OTL principle, which can be obtained if possible upright with transformer all these benefits. The advantage to couple a outpt transformer to an OTL circuit is that the repercussions and influences on the circuit itself ( either headphones or transformers ) are considerably lower. And this brings a projection on presence in the music, the listener will appreciate very quickly.
Everything else on this project was for me then just "routine". A new circuit board develop, expand the circuit according to the light of all electro - physical principles and my over 45 years of experience in this topic. And ladies and gentlemen, I am more than satisfied with my work, I hope you are there also - Helmut Becker
power consumption: 80 VA nominal - 120 VA full load
In summary, this means:
Note: Thus is L U M I N A R E the ONE AND ONLY headphone amplifier on the market that is able to drive all standard headphone loads, starting from 3 ohm up to 145.000 ohms.
OTWIN MAAS - Moderator OPEN-END-MUSIC, Germany
"Dies ist der beste Kopfhörer - Verstärker mit dem ich jemals zu tun hatte"
"Den Violectric V281 konnte ich mir im Vergleich mit dem Luminare anhören. Er ist ein gelungener KHV, der aus meiner Sicht klanglich über dem Vorgänger V200 steht, jedoch in der Gesamtbewertung nicht an einen Luminare heranreicht. Er hat nicht dessen Klarheit im Klang, stellt nicht dessen dreidimensionalen Raum hin und erreicht ihn auch nicht in Sachen Klangfarbe bzw. natürlicher Darstellung. Aus meiner Sicht bedient ein Luminare eine Klasse, die komplett über einem V281 liegt." [ O. Maas)
The Violectric V281 I could listen to me compared with the Luminare. He is a successful amp, which is in my opinion sound than its predecessor V200, however, does not come up in the overall assessment of a Luminare. He does not have the clarity of the sound does not put out its three-dimensional space and also does not reach him in terms of tone and natural representation. In my view, a Luminare served a class that is completely a V281. [O. Maas)
Egal ob mit hoher oder mit niedriger Impedanz, mit hohem oder geringem Wirkungsgrad, egal ob dynamisch oder Magnetostat - keinen der angeschlossenen Kopfhörer habe ich bisher so erlebt, wie über den RKV 3, da öffnen sich tore zu neue welten.
No matter if high or low impedance, high or low efficiency, whether dynamic or magnetostat - none of the connected headphones I have ever experienced so how about the RKV 3, it will open doors to new worlds.
Aucune importance si le casque connecté présente une haute ou une basse impédance, une sensibilité élevée ou faible, qu'il soit électrodynamique ou isodynamique. Quel que soit le casque utilisé, je n'ai jamais connu un tel résultat que celui obtenu avec le RKV 3. Il ouvrira les portes sur de nouveaux mondes.
review by Dr. Martin Mertens, EAR - IN, 2/3 - 2015 ( RKV 2 + 3, basic concept for LUMINARE )
LOW IMPEDANCE mode: - test load 32 Ohm:
1 Khz - 0,1 watt - 0,06 %
bandwide: 15 - 100.000 Hz
OTL mode: test load 220 Ohm.
1 Khz - 0,1 watt - 0,015 %
bandwide: 12 - 150.000 Hz
max. load 2000 ohms - min. load 50 ohms
STAX mode: ( auto gain control )
bandwide: 15 - 150.000 Hz
|gain overview :
Mode: Low-Imp ~ 16.5dB / and STAX connector 32dB + 10dB ( galvanic coupled sym. balanced complementary output STAX connector signal ) + 38 db
Description of some technical details ...
The output impedance at Luminare with negative feedback (physical concept: closed loop) is defined as follows. The control is based on the principle of negative feedback of the open loop gain ( 133 dB ) of the amplifier. However, since there is a closed loop. Dynamically because the amplifier tries to keep active voltage at the output losses in upright because he continuously compares its actual value (feedback) to the desired value (signal) and continuously readjusts addition, through the entire range.
Example: The OTL mode provides Luminare 1V without load resistance and 0.998 V at 60 ohm load resistor. From these data you calculated easily approximated the output impedance of the amplifier for this load resistance 0,12 ohm. The fact of wanting to determine the output impedance by incorporating the tubes, is simply nonsense. It's not the tube determines the output impedance, only the overall OTL concept. of the circuit is the basic for the definition of the output impedance of this circuit concept - this applies equally to RKV 2 + 3 and Luminare. The output transformer is not part its gain loop. Who is interested in the incoming circuit design, can read my patent in 1982. Click here
Explanation of the + 10 db gain switch circuit for Stax mode.
A green internal LED of the front left on the board signals, that LED on gain increased by an reed realis up to +10 db.
|This white LED indicates when the bias voltage built up for the Stax headphones and stable.
|If you turn on the amplifier, reducing the volume and wait until this red LED goes off. As long as this red LED seems light up, all outputs of the amplifier is short-circuited and thus protect the headphones when the amp load or un - load the internal caps. This is always the case when the amplifier ON and OFF switches.
|The transformer was installed outside of the amplifier. This has the advantage on that the heat of the power transformer remains from the device and, second, that no stray magnetic fields cross the output transformer or the circuit board and modulate them. In addition, the transformer was covered with a layer of transformer sheet and thus absorbs stray magnetic fields. Then the transformer with a 2-component potting shed was in a metal cup.
( more informations on our DAC pages )
Warranty and tube Note
On each board is the model name of the product and the name of the tubes is set. So if you are not sure which tube you need, please look at the circuit board and watch what is written there (PCL805 - or ECL85 (6F5P) In mid-2015 has been changed from PCL805 on ECL85 ( 6F5P ) that affects the models RKV all, Luminare and Solaris
The picture below shows you the max. Output voltage before start soft clipping in OTL mode at 220 Ohm load per channel - at 43 Vrms are on each channel 8,3 watts with russia 6N5P
Again and again we get the question how it is possible that our headphone amplifiers on the PRE OUT deliver such excellent results. For this reason, we have done our best to show you what is available at the output of the PRE OUT. If we assume a signal voltage of 1 V at this output (most power amplifiers are already well controlled), we determine an incredibly low distortion factor, which in principle provides a statement about the extent to which the original input signal passes through the headphone amplifier without falsification. This low value is a sensation in itself - the fact that the amp then runs without load - i.e. without headphones - is certainly an advantage.